PRODUCTS

We provide solutions that meet the constantly growing requirements of your data center.

With the next-generation of connection rates, processing and switching technology, and speed are all beginning to outrun connectivity. As speed scales upwards, so does power and cost- adding layers of complexity and attacking reliability.

Designed for high volume production at the lowest power, the AuraDP™, electro-optic coupling technology takes the optical energy off the circuit board and out to the connector more efficiently and more accurately than any other technology. It is a speed-independent, “snap and go” assembly that is common for all products, from 25G up to 800G.

Enabled by our proprietary AuraDP™ technology, high quality products provide exceptional optical coupling efficiency between the optical devices and the MPO connector enabling low power consumption, superior performance and reliability. As a result, we produce low-cost, high yield transceivers that meets the increase in speed and demand.

Trasceivers
  • 400G
  • 100G
Active Optical Cables
  • 400G
  • 100G
400G QSFP-DD SR8 100 Meter
Superior Performance

The DustPhotonics QSFP-DD-SR8 is a hot pluggable transceiver designed for 400GB/s optical links of up to 100 meters over OM3/4/5 multi-mode fiber. The transceiver is IEEE 802.3bs 400GBASE-SR8 and QSFP-DD MSA compliant for use in Data Centers, High Performance Computing (HPC), and Enterprise applications.

Technical Overview
  • DustPhotonics AuraDP™
  • 9W typical
  • Multi-rate support up to 400Gb/s
  • Hot pluggable
  • 100m over OM3/4/5
  • MPO16 interface
  • 0° to 70°C
  • CMIS 4 I2C Interface
  • Tx and Rx selectable retiming
  • IEEE 802.3bs 400GBASE-SR8
  • QSFP-DD MSA compliant
  • ROHS-6 compliant
400G QSFP-DD-DR4
Built for high-yield production

DustPhotonics' 400G QSFP-DD DR4 is an ideal solution for data center interconnects. It employs PAM4 modulation technology to deliver data rates up 400G (8x50Gb/s electrical interfaces).

The design provides an 8-lane electrical interface compared to the traditional four-lane interface, thereby increasing bandwidth, channel capacity and port density. The module converts 8 channels of 50Gb/s (PAM4) electrical input data to 4 channels of parallel optical signals, each capable of 100Gb/s operation for an aggregate data rate of up to 400Gb/s. Reversely, on the receiver side, the module converts 4 channels of parallel optical signals of 100Gb/s each channel for an aggregate data rate of 400Gb/s into 8 channels of 50Gb/s (PAM4) electrical output data.

AVAILABLE AS OF Q4 2020.
Email us for more information.
Technical Overview
  • Hot Pluggable compliant QSFP-DD Revision 5.0 transceiver
  • Low power dissipation
  • Multi-rate support up to 400Gb/s
  • 2000m over single mode fiber
  • MPO12, APC interface connector
  • 8x53.125Gb/s electrical interface (400GAUI-8)
  • Electrical specification 802.3bs (Annex 120E 400GAUI-8 C2M)
  • 0° to 70°C
  • Proven High Reliability Technology: EML and PIN
  • Embedded signal loss and return indication to switch
  • QSFP-DD CMIS Rev 4.0
  • IEEE802.3bs 400GBASE-DR4 compliant
  • ROHS-6 compliant
100G QSFP28 SR4 100 Meter
1.7W

DustPhotonics DPQT-E100-000 is a hot pluggable QSFP28-SR4 transceiver designed for 100 Gb/s Ethernet links of up to 100 meters over OM3/4/5 multi-mode fiber. The transceiver is IEEE 802.3bm 100GBASE-SR4 and QSFP28 MSA compliant for use in Data Centers.

Our 100G QSFP28 SR4 provides up to 4X more reliability. This not only saves on the direct tangible cost of replacing the failed units but also the intangible cost of service down time.

Technical Overview
  • DustPhotonics AuraDP™
  • 1.7W typical
  • Multi-rate support up to100Gb/s
  • Hot pluggable
  • QSFP28 form factor
  • 100m over OM3/4/5 fiber
  • 0°C to 70°C
  • SFF-8636 I2C interface
  • IEEE 802.3bm 100GBASE-SR4 & CAUI-4
  • ROHS-6 compliant
100G QSFP28-eSR4 300 Meter
300M over OM4

The DustPhotonics DPQT-E100-300 is a hot pluggable extended reach QSFP28-SR4 (QSFP28-eSR4) transceiver designed for 100G Optical links of up to 300 meters over OM4/5 multi-mode fiber. The transceiver is IEEE 802.3bm 100GBASE-SR4 based and QSFP28 MSA compliant for use in Data Centers, High Performance Computing (HPC), and Enterprise applications.

Technical Overview
  • DustPhotonics AuraDP™
  • 2.0W typical
  • Internal CDR
  • MPO Optical connector
  • Multi-rate support up to 100Gb/s
  • Hot pluggable
  • 300m over OM4/5
  • 0° to 70°C
  • SFF-8636 I2C interface
  • ROHS-6 compliant
400G QSFP-DD AOC
High Reliability

DustPhotonics DPDA-E400-XXX are hot pluggable QSFPDD Active Optical Cables designed for use in Data Centers, High Performance Computing (HPC), and Enterprise applications. The DPDA-E400-XXX supports digital diagnostic monitoring for supply voltage, temperature, transmit/receive power, VCSEL bias with selectable retiming for transmit and receive directions and is compliant to CMIS 4.

Technical Overview
  • DustPhotonics AuraDP™
  • Data Rate 53.125 Gb
    • /s per lane
  • PAM4 Modulation
  • 9W typical per end
  • Multi-rate support up to 400Gb/s
  • Hot pluggable
  • 5, 10, 15, 20, 25, 30, 50, 100m
  • 0° to 70°C
  • CMIS 4 I2C interface
  • Tx and Rx selectable retiming
  • QSFP-DD MSA compliant
  • Jacket Cable L8ZH
  • ROHS-6 compliant
100G QSFP-DD AOC
1.7W per End

The DustPhotonics DPQA-E100-XXX are hot pluggable QSFP28 Active Optical Cables designed for use in Data Centers, High Performance Computing (HPC), and Enterprise applications. The DPQA-E100-XXX supports digital diagnostic monitoring for supply voltage, temperature, transmit/receive power and VCSEL bias.

Technical Overview
  • DustPhotonics AuraDP™ with improved efficiency
  • Internal CDR with bypass mode
  • 4 channel full-duplex operation
  • 1.7W typical per end
  • 3.3V operation
  • Multi-rate support up to 100Gb/s
  • Hot pluggable
  • Available lengths 5, 10, 15, 20, 25, 30, 50, 100m
  • 0° to 70°C
  • Jacket cable LSZH
  • SFF-8636 I2C Interface
  • ROHS-6 compliant
CONTACT US